hmce industries

IMER Mortarman 360 Series Mixer

9 cu. ft. of mud every three to four minutes. Perfect for busy precast mixing operations system. The discharge system is now easier to open and close and better protected from being hit by the mud bucket or forklift. The safety grate has been improved, it is now hinged, access for clean up is immediate and complete. Mini Batch Plant production for the cost of a mortar mixer.

• Free shipping from IMER factory warehouse
• Further study and testing have lead to drum and paddle design changes that vastly improve batch output, mix 800 lbs. of material every load.
• The paddle systems are powered by monster gearboxes which were developed in our batch plant division.
• Mixes 800 lbs of mortar, dry pack, stucco, or sand & cement
• Electric motor 220V is available in Single or Three Phase, specify when ordering.

• The science behind vertical shaft mixers is quite simple. The paddles are in the mix 100% of the time. The material is blended with a stirring action as opposed to a flipping action which high speed film shows is a more aggressive and thorough mixing action. The material is scraped from the side of the drum by the big sweeping arm and lifted from the pan by the lower paddle to ensure uniform and consistent mix. A trident paddle finely blends the material. Imer mixers do not trap aggregate down at the bottom of the mixer which jam up the paddles in conventional mortar mixers. Vertical shaft mixers are great to handle dry pack, grouts, thin sets, stuccos, self-leveling materials and

Imer Blockhead Masonry 500

The Masonry 500 block head delivers fast, accurate, vibration free cutting performance.

• Free Shipping from IMER factory warehouse
• 16" x 16" Heavy Duty table has room to cut 2 - 8" blocks at one time
• Enough tray travel to lock head and push material eliminates pull down cutting
• 9 hp Honda motor with oil clutch and single ribbed belt is vibration free
• Available with 5 hp 220V Electric motor
• Emergency stop switch with in easy operator reach
• The Stand is built into the frame (14" and 20" saws) for stable and secure cutting
• Honda gas motors with centrifugal clutch eliminates the need for jack shafts and pulleys
• Electric 110 Volts models are designed to run anywhere with ease; breakers won't trip on startup!
• Locking stainless steel protractor comes standard with all saw models
• Removable poly trays for easy cleanup
• Cut blocks the 12" way to cut out webs for bond beams

• The cutting tray roller system is the best in the industry.
• The two 1" steel guide bars provide great accuracy and are fully adjustable.
• This saw will remain accurate for years to come!

• The single arm frame design allows the passage of large or irregular materials.

Wacker RD 16-90 Hydrostatic Vibratory Roller

WACKER's RD 16 roller features dual drum drive for maximum traction and articulated steering for extremely accurate control. Diesel-powered unit offers dual drum vibration for a high quality asphalt finish. Outstanding overall roller performance and a high exciter frequency allows compaction at faster speeds while still delivering even coverage and excellent results. Features

• Pressurized water system offers consistent water flow. An eight-position timer allows operator to adjust water flow and match conditions.
• Overall machine design eliminates overhang of unit. Easily maneuverable units provide flush, right up to the edge asphalt compaction.
• Rear platform and front hood tilt up for easy access and improved machine serviceability.
• The RD 16 features a reliable Lombardini diesel engine for high performance and standard foldable ROPS for easy transport and storage.
• Ergonomically designed operator's platform features a fully adjustable suspension seat for maximum comfort and the sloped hood provides for excellent visibility.
• Designed for compacting base and finish layers of asphalt as well as granular subbase material in confined areas. Ideal for parking lots, driveways and shoulder work.

Wacker DPU 5045H Diesel Reversible Vibratory Plate

These vibratory plates offer the best compaction of various types of soil. They show their true strength when working on semi-cohesive soils in particular. These reversible plates provide optimum performance along with a variable forward and reverse speed of up to 79 ft/min (24 m/min). Plus, the dual shaft exciter technology provides the maximum possible compaction depth in most types of soil. Features

• Infinitely variable forward and reverse operation including spot compaction for easy maneuverability. Ideal for trenches and over large areas, also for vibrating heavy interlocking paving stones.
• These low profile units feature standard extension plates providing adjustable operating widths.
• The ductile iron baseplate (GJS-700) is impact and wear resistant ensuring long operating life.
• An adjustable guide handle can be moved to a vertical position for operator convenience during tight turns. An optimum shockmount design reduces handle vibration, operator fatigue and engine wear.
• A heavy-duty roll cage and lifting eye provide for easy loading and placement into trenches.
• The hydraulic steering has been combined with a dead man's handle for added operator safety.

Wacker RD 7H-ES Double Drum Vibratory Roller

This walk-behind, double drum vibratory roller is capable of performing a wide range of soil and asphalt compaction applications. The exclusive compact design allows for tight side clearance on both sides of the roller. Plus the totally hydrostatic drive eliminates mechanical components providing for less maintenance and greater reliability. Features

• Dual smooth drums with beveled edges compact asphalt and granular materials equally as well for added job versatility.
• Roller features a low oil shutdown for maximum engine protection.
• Guide handle folds for compact storage, and features excellent shock mounting for low vibration to operator.
• Large rubber shock mounts absorb vibration and shock to the upper components, reducing equipment wear and operator fatigue.
• Unit features easy to operate handle with vibration control for improved operator comfort and convenience.
• Unique clutch/pump drive system provides easy cold weather starting and allows for no-load starting of engine.

Wacker Single Drum Vibratory Roller

Ideal for smaller repair and maintenance jobs
Lightweight and highly maneuverable roller has infinitely variable hydrostatic drive for in smooth, even accelerations. Excellent choice for the compaction of sand, gravel, soil and asphalt on roadways, walkways, bridges and parking lots. High curb clearance and close side clearance to accommodate work adjacent to curbs and walls.

Features

Rounded edge steel drum has adjustable and reversible polyurethane self-cleaning scrapers to prevent soil and asphalt buildup between the frame and the drum giving smooth and uniform surfaces. Automatic braking system in forward and reverse for operator safety. Transport drive system is fully enclosed, increasing component life for continued operation and higher production. Maintenance-free drum drive is also fully enclosed to eliminate dirt and grease accumulation, reducing service time and increasing productivity. Adjustable, enclosed handle improves operator comfort and folds vertically for convenient transportation and storage. Large anti-rust coated water tank reduces stops for refilling for continued operation and high productivity. Snap-out sprinkling system and in-line filter screen are easily cleaned, reducing downtime. 3,400 lbs centrifugal force RS800A recoil start, RSS800A electric start with recoil back-up.

Wacker BFS 1318A Gasoline Floor Saw

Ideally suited for a wide variety of applications
The Basic floor saw is ideal for all standard cutting applications. Most of the cutting tasks on the job site can be taken care of with versatility and without complications. The simple, well thought-out design combines high performance with easy handling, allowing for a variety of applications without problems.

Features

• The unique, ergonomic handle system makes individual adjustments of the handle width and height possible, thus allowing for optimum operator control of the machine.
• Extremely high cutting performance with a cutting depth of 6.5†(16 cm) when using a 18†(450 mm) cutting blade.
• The water tank puts pressure on the cutting blade, thus making for very stable cuts.
• The BFS is so light that it can be easily lifted by two people.
• The central lifting point, integrated in the durable protective cage, plus the foldable guide handles make transporting the machine extremely easy.
• Unit features large, removable, 33.8 quarts (32 liter) capacity water sprinklers on both sides of cutting blade.
• Heavy-duty WACKER engine provides outstanding performance.

Wacker EH 27 Electric Breaker Buy a Wacker Eh27 with cart chisel and point and save EH27 was $1539.99 now only $1399.99

These electric universal breakers can be used, in addition to breaking up and demolition work, for driving in earthing rods as lightning conductors, driving in piles using special hoods, and ramming in probes to obtain soil samples for geological purposes and environmental soil examinations. The telecommunications construction sector, and fencing/tent building companies are also frequent users of this type of equipment.

• Driven by a powerful tried and tested electric universal motor with protective insulation for connecting directly to the mains.
• A specially designed protective hood, which is made of shock-resistant plastics, ensures excellent cooling of the motor as well as ensuring good noise suppression.
• The vibration-damped handles and, in particular, the almost recoilless air-cushioned percussion system, ensure a practically vibration-free operation.
• Thanks to the optimum spring mounting of the three operating handles and the complete engine protective hood this machine is suitable for long periods of operation.
• Standard with 10 m / 33 ft. power cord.
• EH 27 comes with a point, chisel and hammer cart

Technical Data EH 27

BS 50-2 Two Stoke Rammer Tamper

WACKER's WM 80, 2-stroke engine, built for tough rammer applications

The Wacker BS 50-2 jumping jack plate tamper rammers have set the standard in the construction industry. Wacker tamper rammers are powered by the exclusive WM 80, the only 2-stroke engine specifically designed and built for vibratory rammers and meets EPA standards. WACKER's rugged jumping jacks are designed for maximum production, performance and durability.

Features & Benefits BS 50-2

• Patent-pending vented carburetor evacuates air from the fuel line for easy starting.
• An integrated fuel valve and gas lever also provide for simple operation and easy starting by eliminating air in the fuel line.
• A unique three-stage air filtration system provides a virtually dust-free engine for longer life and improved durability.
• A filter minder tells the operator when the air filter needs to be changed.
• The guide handle offers a highly engineered, built-in shock-mount system to reduce HAV (hand-arm vibration) and improve operator comfort.
• Rugged rammers designed for the compaction of cohesive, mixed and granular soils in confined areas.

Wacker Hatz Diesel PT2H & PT3H Trash Pump

Centrifugal trash pumps are designed to keeping jobsite dry
WACKER's centrifugal trash pumps have proven themselves on jobsites around the world.
With an optimized impeller design and built-in contractor friendly features, this line of trash pumps has redefined the quality and durability standards of self-priming centrifugal trash pumps.

Features and benefits

• Self-priming high performance pump capable of handling solids up to 1.5 inch, ideal for most jobsites that require fast dewatering on command.
• Hardened ductile iron impeller and volute with a patented volute insert provides a rugged, easy to maintain pump that will stay on the job longer.High strength, lightweight aluminum housing, compact with easy access, allows extra years of trouble-free operation.
• High strength lightweight diecast aluminum housing increases the years of trouble-free pump life.
• Radial flow design produces high volume and head for superior pump performance.
• Quality components such as carbon ceramic mechanical seals for extra long life.
• Diesel trash pumps offers maximum production, performance and durability while providing you the convenience of standardizing your diesel fleet.

Wacker PT 6LT 6" Centrifugal Trash Pump

Heavy duty centrifugal trash pump designed to keep your jobsite dry
WACKER's self-priming, high performance centrifugal trash pumps have proven themselves on jobsites around the world. Featuring electric start and a thread-on mixed flow impeller design, this trash pump has redefined the quality and durability standards of self-priming centrifugal trash pumps.

Features and benefits

• Self-priming high performance pump capable of handling solids up to 2", ideal for most jobsites that require fast dewatering on command.
• Hardened ductile iron impeller and volute with a patented volute insert provides a rugged, easy to maintain pump that will stay on the job longer.Thread-on mixed flow impeller design produces higher volume and head for increased pump performance.
• Heavy-duty frame with central lifting point and pneumatic tires combine pump and engine protection with easy transport.
• Mechanical seal runs in oil bath to reduce maintenance and protect seal in dry-run conditions.

>

Wacker Walk-behind Trowels

Trowels feature high quality finishing plus triple protection
Designed and built with the most advanced technology, Wacker’s walk-behind trowels offer high quality concrete finishing plus added operator safety. The patent-pending gearbox brake, gyroscopic safety sensor and engine speed limiter provide triple protection for the operator. This unique system minimizes a runaway handle situation and meets worldwide safety requirements.

Features and Benefits

• Dynamically balanced trowels (when blades are turning) offer nearly effortless operation.
• Optimum weight distribution reduces the lateral force from the trowel for reduced operator fatigue.
• Trowels feature a 30-degree blade pitch for better concrete burnishing.
• For maximum flexibility, engine type, trowel diameter and handle type can be selected to meet individual preferences or job site conditions.
• (Handle sold separately.)
• Guard ring features tubular framing for easy cleaning and maintenance.

Wacker BTS Gasoline Power Cut-Off Saw 12" & 14" Guards To get the best out of your Wacker cut-off saw use synthetic 2-cycle oil mix
Unique piston provides outstanding performance

General Features

• These portable cut-off saws (BTS series) prevent piston jamming and are thus unbeatable when it comes to performance and economic efficiency.
• Their extreme ruggedness is based on the unique "L3" piston; the name L3 refers to "Long Life Lubrication".
• The innovative air cleaner design and the improved engine cooling system provide for added reliability.
• The BTS series offers the highest power to weight ratio of their class plus outstanding ergonomic features.
• The "Long Life Lubrication“ L3 piston has been furnished with a special graphite surface coating to eliminate piston and cylinder overheating even during tough continuous operations.
• This special coating also provides protection against dirt and reduces the need for lubrication.
• Units feature an operator-friendly air cleaning system where the air flow is such that the dust is automatically shaken off the preliminary filter through the machines own vibration.
• Plus the 54 % larger filtering surface of the air cleaner noticeably increases the filter's service life.
• Water kit is assembled to saw and can be used with garden hose, gravity tank or pressure tank
• The increased cooling air supply optimizes the engine's protection against overheating.
• 50-1 Fuel Mixture, 37oz fuel tank Capacity
• The starter rope has been treated with silicone, thus providing added protection against rope damages for rugged operation.
• The blade guard can be adjusted effortlessly and infinitely by hand, thus allowing for quick and easy set-up times.
• Shown with optional diamond blade.

Wacker G 50, G 70, G 85 Mobile Generator

Heavy-duty mobile generator for reliable power.

Features:

Compact, sound-attenuated generator provides single and three-phase power for construction, commercial, industrial and special event applications where quiet, reliable power is needed. A solid state digital information center monitors generator output and engine functions plus provides protection against engine and generator faults as well as standard automatic remote starting for standby applications. Skid-mounted units feature a fully integrated, large capacity fuel tank for long run times, even without a trailer.

• Unit offers low noise, mobile power for virtually any sound-sensitive application. Utilizing proven technology and simple design, this quiet generator provides excellent reliability in the most demanding environments.
• Brushless generator features a separate excitation winding for excellent motor starting and an enhanced ability to run non-linear loads.
• Durable features like stainless steel external hardware and automotive corrosion treatment of select body parts provide a long-lasting, quality appearance ensuring a high resale value.
• Generator control panel swings open as one complete unit for easy service-ability.
• Factory-installed customized options are available. These include, but are not limited to, a fluid containment system, an electronic governor and additional camlock panel.
• Optional 6,000 lbs single-axle trailers are fully equipped and highway ready with DOT lighting, chains, height adjustable coupler and electric or hydraulic surge brakes.

• Battery 12V/720 CCA
• 1 Ø 120V - 20 A GFI duplex X 2
• 1 Ø 120/240V - 50 amp twist lock X 2
• 1 Ø 120/240V-30 amp twist lock X 1
• Trailer hitch type 3 in Pintle

Wacker GV 6600A Portable Generator

Commercial grade portable generator series built with the value conscious contractor or do-it-yourselfers in mind. Offering just those job site proven features that are really needed, these generators are ideal for powering your WACKER electric pumps, breakers, drills, concrete vibrators, as well as saws, lights, heaters, etc. These generators are also ideal for home and small business temporary power or powering job site trailers.

Wacker GV 5600A Features:

• Powered by commercial grade Honda OHV engine with low oil shutdown and one pull start for optimum performance.
• Automatic engine idle control reduces engine wear, noise and fuel consumption.
• Large steel fuel tank, featuring an easy to read fuel gauge, offers long run times between fills.
• All components are protected by a durable wrap-around steel tube frame.
• Maintenance free alternator with separate excitation winding and AVR (automatic voltage regulation) for superior voltage regulation and best in class tool starting.
• Full 120V power switch for maximum 120V or 120V/240V power, ideal for a wide variety of applications.
• GFCI (neutral bonded to ground) protected 120V duplex outlets complies with OSHA job site requirements.
• Large muffler provides for quiet operation.

Technical Features

Northrock Pro 50 4S Backpack Concrete Vibrator

• Honda GXH-50 4-Stroke Engine, Uses regular gas, no need to mix oil with gas
• High efficiency synchronous drive belt transmission with cast aluminum housing that steps up engine speed to achieve optimal vibrations per minute
• Universal counter shaft accommodates all brands of vibrators so you can use the shafts and heads you already stock
• Strong steel tubular frame with ergonomic molded back pad and padded shoulder straps
• Power vibrator heads from 3/4" to 2 1/2"
• Free shipping

Northrock Electric Vibrator Power Units

• Available in three power option : 1-1/2 hp, 2 hp & 3 hp
• Free shipping
• 1-1/2 hp max head diameter 1.75"
  2 hp & 3 hp max head diameter 2-1/2"
• High strength cast aluminum housing
• Rugged shock absorbing frame
• Easy access to all serviceable parts
• Shaft length and head diameter available up to 2-1/2" in diameter
• Motor size is selected to maintain an in-material working frequency of about 10,000 Vpm under load
• Weight: 1-1/2 hp 19 lbs, 2 hp 23 lbs, 3 hp 25 lbs.
• 1-1/2 hp 13 Amps, 2 hp 15 Amps, 3 hp 19 Amps
• All Northrock power units may be configured to drive alternate brand shafts and heads
• Serviceable parts are easily accessible
• Replacements shaft and heads available form the following brands:

Northrock Pro 3200 Series Power Screed

• Eccentric design with 60% more power for high productivity and ease of use.
• Wrap-around frame design provides greater strength and better isolation.
• Patented magnesium blades cur and roll the concrete in front of the screed, reducing the need for grading while the ten inch wide shoe promotes flatter floors.
• Available with blades form 4 ft to 14 ft for one man operation and 16 ft to 22 ft for two man operation.
• 31cc. 4 cycle Honda gasoline engine power a well engineered and field proven eccentric system to frequencies up to 6000 Vpm.
• This system is mounted on an angle to the blade, allowing the vibration to be transmitted both horizontally and vertically.
• The combination of high frequency combined with the angled eccentric system design promotes smoothness and rapid consolidation of the mix.
• Large rubber shock mounts direct vibrations away from the operator and down into the mix.
• A strong, light weight frame allows the blades to be changed in seconds while the pull handles adjusts quickly to the operators height for optimum productivity.
• Power unit and frame weigh in at only 28 lbs making the system easy to maneuver and transport around the site.
• Max bar length 12 ft. per power unit.
• 10 ft to 22 ft bars ships by truck freight.

Dynapac Hatz Diesel LG500 33x35in Forward & Reversible Soil Plate Compactor

The LG500 offer a heavy-duty reversible plate with high compaction performance. A powerful Diesel engine makes the LG500 an economical attractive alternative to heavy vibratory rollers. The wide base plate is designed for fast compaction of soil and stone material on large surfaces, and also for building foundations and backfill against supporting walls.

Features

• For soil applications
• Electric start
• Forward and reversible plate compactor
• Hardox 400 bottom plate
• Servo hydraulic Forward/Reverse controller

• Engine: Hatz Supra 1D81Z
• Horsepower: 12.4
• Fuel Type: Diesel
• Plate Size: 33" x 35"
• Amplitude: 0.08"
• Frequency: 3,600 VPM
• Centrifugal Force: 13,500 lbs
• Weight: 1,047 lbs
• 1 Year Limited Warranty

Dynapac Hatz Diesel LG300 24x29in Forward & Reversible Soil Plate Compactor

The LG300 Hatz Diesel forward and reversible plate compactor is an heavy-duty plate for soil applications, ideally used for compaction of backfill in pipe and cable trenches, as well as road repair and maintenance work. Speed and compaction depth are regulated steplessly via hydraulic servo control of the eccentric element. This gives the plate smooth motion and makes it very easy to operate. The design includes a strong cover that withstands severe shock and also protects all vital parts of the machine.

Features

• For soil applications
• Forward and reversible plate compactor
• Hardox 400 bottom plate Forward/Reverse controller

• Engine: Hatz 1B30
• Horsepower: 7
• Fuel Type: Diesel
• Plate Size: 24" x 29"
• Amplitude: 0.07"
• Frequency: 4,200 VPM
• Centrifugal Force: 9,000 lbs
• Weight: 662 lbs
• 1 Year Limited Warranty

Dynapac LX90 18" Round Forward Soil Plate Compactor

The LX90 vibratory plate compactor features a unique round base that allows flush compaction next to posts, pillars, guardrails, manholes, drainage inlets and foundations. The design of LX90 makes it easy to maneuver around obstacles.

Features

• For soil applications
• Hardox 400 bottom plate
• Unique styling for confined areas
• Vibration damped handle
• Oil alert

• Engine: Honda GX160
• Horsepower: 5.4
• Fuel Type: Gas
• Plate Size: 18" round
• Amplitude: 0.07"
• Frequency: 4,500 VPM
• Centrifugal Force: 3,600 lbs
• Weight: 212 lbs
• 1 Year Limited Warranty

Dynapac LT800-11 Diesel Rammer

The LT800 diesel rammer is suitable for compacting soil in trenches, around poles and in restricted spaces. It has been designed to comply with contractors' highest demands in terms of efficiency, simplicity and operators comfort.

• Hatz 1B20, 4.6 HP Diesel
• LT800 4.6 hp, 9"x13" shoe size, Impact force, 21.4 kN/blow
• Weight 185 lbs, 84 kg

Dynapac BG Power Trowels
Facility to operate our machines is also one of our key concerns, this is why ergonomics and safety are always maximized when designing our trowels: less strain on the machine’s operator and the highest safety standards also contribute to maximizing output when working with a Dynapac BG trowel.

Features & benefits

• Designed for maximum ergonomy and capacity.
• Long and foldable galvanized handle and wheels
• Two-stage helical gear giving the gear box 100% efficiency.
• Safety handle stopping the engine within a quarter-turn when the handle is released

• BG-24" blade diameter, Honda GX120, 4 Hp
• BG-36" blade diameter, Honda GX160, 5-1/2 Hp
• BG-46" blade diameter, Honda GX340, 11 Hp

• The first pass (rough trowelling) with smoothing disk can take place as soon as the concrete can be walked on.
• The second pass (fine trowelling) with multi-purpose blades can take place as soon as you can press the concrete with the hand without collecting concrete on it.
• Average wear of the multi-purpose blades with standard concrete mix: 1500 sqm.
• All our blades are reversible !

Dynapac 18" ORKA Floor Saw

Dynapac floor saws: a compact range covering most common cutting applications.

• Used in the building industry to cut trenches and make expansion joints, ORKA floor saws are also extensively used in road repair works to cut asphalt stripes.
• With a decisive edge over other techniques they economically perform a very accurate job
• A fork-watering device, i.e: constant cooling of the diamond disk on both sides, improved evacuation of dust and waste while in operation.
• Honda engine with a cyclonic filter improving the engine’s lifetime.
• Optimal balance of the machine for accurate cutting

• Combined diameter 14"/18", 350/450 mm in one machine (suitable for diamond blades up to 18" 450 mm)
• Max cutting depth with 18" blade is 6-5/8" 175mm
• Equipped with a 13 hp HONDA GX390 QXC4 engine
• Reversible handle: reduced height and width for transportation
• “V-poly†belts
• Fork-watering device
• Water tank capacity 30 L
• Weight 216 lbs, 98 kg

Belle Group Trench Rammer

Features

• Reliable, easy to start Honda 4 cycle gas engine
• Low exhaust emissions
• 3 Fuel filters and a large capacity air filter improves service
  life in harsh conditions
• Precision direct gear drive with oil bath lubrication system
• Extra tough heavy duty bellows protect internal parts from abrasive dirt
• Perfect balance improves performance and reduces
  the effort required to operate
• Heavy duty, chromed steel protection frame
• Adjustable handle height for improved operator comfort
• Recoil protection

Weight

RT 50 121 lbs RT 65 147 lbs RT 66 145 lbs RT 74 165 lbs

Belle Group PCLX Compactor

Advantages

• Comfort handles help reduce operator fatigue
• Low hand-arm vibration levels, patented and registered design
• 12.6in or 15.7 in base width-choice to suit application
• Complete with lifting eye
• Street-works 12.6" plate has 3/4 ton roller compaction.
• Optional large capacity (2.8gal.),Quick-release water tank
• High quality vibrator gives reliability and performance
• Manual handling points for an easy two man lift

Belle Group BWR 650 Duplex Roller

Kubota E75NB3-BWR 650 Diesel water cooled electric start Low noise emission High compaction force 4500 lbf/drum Water tank capacity 9.25 gal Minimum overhang for close-to-wall applications

Features

Free shipping from Belle Group warehouse Strong heavy duty design and tipping mechanism Can easily handle loads of up to 661 lbs Climbing ability of up to 38 degree inclines Usable in 2 or 4 wheel drive modes 28", ideal for small spaces Gear box with 4 forward gears Equipped with reverse gear and disc brakes 4 x 4 Multipurpose tires Engined positioned to allow easy access and service Equipped with parking disc brake for total operator security Center wheel engaging 4 wheel drive when loaded on rough terrain Perfectly balanced when working with full load Additional bearings to support axle and strengthening plate Bottom protection plate to avoid damage by stones

Options

Flat bed Ramps

Belle Group Minimix 150 Concrete Mixer

• Free shipping from Belle Group warehouse
• Lightweight and portable, the Minimix 150 mixes a full barrow-load
• Will mix 275 lbs mortar or concrete
• Used with the stand, it allows barrow-height mixing and tipping
• Stand included
• Electric motor or Honda gas engine available
• Double insulated electric motor
• Full thermal overload protection

Belle Group Hydraulic Packs

Screed King Honda 4-Stroke GX35

• 75% less vibration to operators hands.
• No tools required to remove screeds bars
• 5.5" base allow the screed to float in any slump of concrete.
• Unique curl edge helps to roll the excess concrete back to the rackers and allows the screed to float or ride on forms.
• No brackets or adjustable torsion rods mean no crevices for concrete to gather-in, making clean-up a breeze.
• Adjustable handlebars can accommodate any user height in any depth of concrete.
• Honda 4-strokes engine is isolated from vibration with rubber mounts.
• No flex shaft to lubricate, oversize bearing system is factory sealed.
• Clamp-on mounting system allows the power head to be offset to work under protrusions
• Screed King delivers high frequency vibration that eliminates the honeycomb effect and speeds finish time.
• Power unit only, bar not included

Crown 16 SH Hydraulic Towable Mortar Mixer

• Free shipping from Crown warehouse
• 7 gauge steel for longer drum life
• 2" solid steel paddle shaft
• Ductile iron paddle are stronger than welded steel, making this mixer the industry's most durable!
• Crowns exclusive Shear Pin Protection system shields the gear reducer and engine from potential damage should an engaged mixer be impeded by a shovel or other foreign object.
• Crown's self-latching drum lock is knee operated, freeing both hands for optional dumping control.
• Extra-Large B78x13 tires for smooth towing to your job
• 4 to 5 bags capacity, 16 cubic Ft.
• Highway towable comes with high speed taper roller bearings, and heavy duty axles for years of trouble-free towing
• High Strength Frame newly designed frame provides improved durability and stronger support in the areas where you need it.
• The raised frame construction allows for convenient dumping for a wheel-barrow.
• Charging Height 58"
• 2 pcs safety grill is stronger, safer and easier to use than a one pcs grill and will not damage the drum
• Lifetime Warranty, All Crown mixers feature a lifetime warranty on the drum bearing and seals.
• Heavy-duty one-piece cast-iron ring gear for longer life
• Spiral blade mixing standard on 16SHydraulic mixers

Crown 9 Cubic Ft Towable Concrete Mixer

• Free shipping from factory warehouse
• Welded drum is manufactured using high abrasion-resistant steel, for longer drum life
• Drive pinions and gear rings are made with cast iron for better durability.
• 2 Sets of laser cut steel blades provides a smooth, fast and more thorough mix.
• New dumping mechanism comes standard with a multi-position drum lock for easy cleaning.
• Extra-Large B78x13 tires for smooth towing to your job
• 1.5 bag capacity, 9 cubic Ft.
• Highway towable comes with high speed taper roller bearings, and heavy duty axles for years of trouble-free towing
• High Strength Frame newly designed frame provides improved durability and stronger support in the areas where you need it.
• The raised frame construction allows for convenient dumping for a wheel-barrow.
• Drum diameter opening 19"
• Drum height 31"
• Lifetime Warranty, All Crown mixers feature a lifetime warranty on the drum bearing and seals.
• Heavy-duty one-piece cast-iron ring gear for longer life
• Comes with standard pintle hitch, ball hitch optional.

Crown 16 Cubic Concrete Buggy

• Free shipping from Crown warehouse
• Extra capacity 4 Gallon fuel tank for longer run times.
• Variable hydrostatic drive system allows you to ease up or down to your desired speed by squeezing the drive lever.
• Removable outside tires to go thru doorways.
• Electro-Hydraulic dumping switch conveniently located on the handlebar.
• The industry's first Buggy with drum brakes, not susceptible to failure due to concrete or dirt build up like other buggy's
• 16 cubic ft cross link polymer bucket also offers the best UV protection.
• Crown's industrial strength hydrostatic system provides enough power to fully supply both drive and dump functions simultaneously without slowing either.
• Heavy steel frame rails run the entire length of the machine providing superior strength
• Riding platform locks in upright position for walk behind applications.
• Max payload 2500 lbs
• Ground clearance 5.5"
• 13HP Honda engine, top speed 7 mph.
• 6" Minimum discharge height, prevents accidental damages forms when backing up with the bucket down.
• Loading or unloading is a snap using either the front or side facing forks pockets or the centered lifting eyes.

SS-300R Concrete Wall Saw Features Chassis can be clamped anywhere on the track 2 speed 300/700 Rpm Easy to read depth gauge. Auto travel control

Standard Kit includes

• 27 amp, 110Volts, single phase electric motor, 2 speed 300 or 700 rpm
• 2 track included one 3.93 ft (1.2m), one 1.97 ft (0.60m) track
• Travel motor with auto travel control
• 30" blade guard.
• Optional flush cut flange available

Diteq Super Premium 4" Dry Polishing Pads

• For wet & dry use
• Great for dry polishing of engineered stone, quartz surfaces or granite
• For faster result, pads should be open (broken-in) wet.
• 9 Pcs KIT Also includes a FREE 4" backer pad
• These extremely flexible pads feature a high diamond concentration that provide the user with superior results at a very competitive price.

Diteq Teq-Grind II Features:

• Full floating head
• Free 8" diamond grinding disc (10 seg)
• Vacuum connection
• Central water feed
• Fold-down handles
• Raise & lower
• Motor: Single phase 2hp electric motor with thermal overload or 5.5 hp Honda engine
• Convenient location for on/off
• Fully powder coated/zinc plated

• Removing paint, epoxy or urethane coatings
• Repairing worn, damaged or spalled concrete
• Leveling uneven or curling slabs
• Grinding hard surfaces, feather edging sidewalks, gutters and similar surfaces
• Grinding high and uneven joints
• Removing excess surface material
• Leveling patches of plastic overlays or grout
• Fast grinding of rough, uneven slab surfaces and drainage control
• Electric model weight only 120lbs including cutting head.

Diteq Blu-Drill TS-132 Core Drill Features

• 9" bit capacity
• Weighs 33.5 lbs
• Free carrying case and 5" water collector ring
• Free tool kit includes 2 wrenches, 2 Allen keys, core removal wedge, anchor stud w/ washer and nuts, and pouch
• Compact 15 Amp, 110 V single-speed (850 Rpm) Shibuya low noise motors
• Built-in on/off switch with low voltage drop-out and motor overload protection
• Slip clutch is adjustable without disassembly
• Multi-position water swivel inlet for convenience
• Roller carriage for smooth and precise drilling
• Right and left hand feed handle positions
• Carrying handle for easy lifting
• 2" x 2" square hybrid steel and aluminum column for light weight and strength
• 31" column with 19" stroke stroke
• 5 3/4" wide x 8" long anchor or angle anchor bases with self-cleaning leveling screws and built-in water collector ring fixture
• Optional removable vacuum pads for versatility
• 1 year warranty
• Tilt stand available. Call for pricing

Diteq ARIX C-43 Segmented Diamond Blade

Wet or Dry.
Patent pending ARIX technology gives you maximum productivity with the lowest possible cost per foot cut. Diamonds are individually placed in strategic positions to maximum cutting performance. Cutting speeds typically increases upwards of 50% while blade life often climbs to 100% more than traditional diamond blades

• Use with walk behind saws and cut off saws
• Use for cured concrete concrete with critically hard aggregates and heavy steel reinforcing
• .393" diamond rim height
• .125" thickness with 1"/20mm arbor

Diteq Blu-Drill RH1531 Hand Held Core Drill.

RH1531 Advantages.

• Ideal for concrete and masonry drilling applications.
• 3-speed gearbox with selector adjusts for various bit sizes (560/1400/2900 Rpm).
• On/off switch for column mount
• Powerful 15 Amp motor comes with carrying case.
• Weight only 15 lbs. 3 speed operation.
• D-style handle for ergonomic control.
• Two conveniently placed leveling gauges and multi-position removable side handle.
• Standard 1-1/4"-7 thread with 5/8"-11 threaded adapter and water connection.
• Equally suited for wet or dry drilling.
• Clutch design patent pending.

Diteq Fast Track Track Saw Features

• Saw never touches material
• Expandable rails
• Cuts 3-3/4" thick material
• Bevel cut, 45 or 50 degrees.
• Self propelled
• Two 7' rail set, (cuts up to 14') two clamps, four locking shoes, connector plate and carriage-mounted motor.
• Locking device for plunge cutting.
• Light weight and portable.
• Optional vacuum system anchors rails to materials.
• Uses 12"diamond blades.
• 15 Amp motor, 115 Volts, 1" arbor.
• Depth of cut 3-3/4".

4" Variable Speed Wet Polisher Kit

• Includes 9 Granite polishing, pads and backer pad
• Grits 50, 100, 200, 400, 800, 1500, 3000, black & white final buff.
• For polishing, shaping and light grinding.
• Designed especially to polish engineered stone which requires low RPMs.
• weight 6.1 lb, Variable speed 800 to 3600 RPM, 115 V, 5.8 AMPS.
• Spindle thread 5/8â€-11 with spindle lock.
• Auto stop carbon brush, double insulated
• Special bearings and dust protection for long life.
• Cord length 8 ft.
• Includes water valve, hose, reversible handle, GFI, faucetgarden hose adapter, wrenches.

Diteq Dry Core Bits For Granite

• High performance bits are laser welded for the ultimate in strength and durability
• 5/8" thread female arbor, fit all wet polishers
• Special diamond segments are ideal for fabrication shops that want to maximize productivity
• Use on granite, marble, and natural stone
• Can also be adapted to construction trade, wherever holes may be needed, water, gas, and electrical piping, especially when natural stone is already installed.

MK Manta III Tilt Base Core Drill Rig

Technical Features Motor Options

• Milwaukee 4094: 3 hp, 115 Volts, 20 Amps Shear Pin. 450/900 Rpm
• Milwaukee 4096: 3 hp, 115 Volts, 20 Amps Slip Clutch. 450/950 Rpm

General Features

• Precision rack-&-pinion carriage with maintenance-free double-sealed bearings
• 2-1/2" steel column with ceiling jack
• Lightweight cast-aluminum base with built-in wheels
• Positive anchoring for vertical & horizontal drilling
• Control box with amp meter
• Removable slide handle easily negotiates close to walls and columns
• Carriage assembly easily detaches from column for convenient transport
• Made in the USA.
• One-year limited warranty

Core Bore M-6 Drill Rig Stand By Core Bore

• Available hydraulic pillow block and extensions with 1-7/8"-7 or 1-1/4"-7 threads for high torque drilling
• Heavy duty 15" x 12" roller carriage
• Equipped with a strong 72" tall, 4" x 6" rectangular mast
• Sturdy cast aluminum base - Steel base available
• 6 inch rubber tread cast-iron wheels with roller bearings
• 18 inch bit capacity with a standard pillow block

M-6 Drill Rig Includes: base, base wheels, mast, carriage, 4-spoke handles, mount for pillow block.

NOTE: Pillow block, motor and spacers must be ordered separately.

Kor-It 24" K-424 Gasoline Powered Core Drill Machines

• Free shipping
• Quick set-up - minimizes time required for each job
• Longer bit life with very stable drilling platform - reduces job costs
• Drill faster with gasoline power - get the job done in less time
• Stand-alone system requires no additional power - field independent
• Heavy-duty, dual-precision ground columns and tenzalloy precision machined carriage assembly
• Smooth-precision ball feed screw system
• Designed for large and small hole drilling - one machine does the work of two
• Accurate drill placement and easy alignment of drill platform
• Drill stand
• 15 hp Gasoline motor with electric start with battery and charger
• Dual-drive shafts
• 24" bit diameter capacity
• Water swivel assembly
• 24" drilling depth

Multiquip Tandem Drum Ride-On Rollers

The workhorse for asphalt contractors, this articulated, vibratory roller can be deployed on many jobs usually reserved for larger asphalt rollers. A wise investment for every contractor who is looking for dependability and productivity.

Features

Articulated movement with power-assist provides accurate, positive steering control and increases maneuverability in confined job sites. Oscillation up to 11 degrees maintains drum contact to the surface. Three-year warranty on articulation joint. Designed for compacting asphalt and sublayer granular and mixed soils Hydrostatic drive with variable speed control for both forward and reverse travel Maintenance-free vibratory assembly Five-year warranty on drive motors 3,100 lbs centrifugal force 4,000 vibrations per minute 1 1/4-inch (32 mm) right side clearance allows close operations near walls and obstructions. Curb clearance of 19 inches (483 mm) insures flush compaction to the curb. Unobstructed driver visibility open, uncluttered operator's platform allows for clear views. Superb engine panel access to all engine and hydraulic maintenance components. Call For Freight Charge

R2000H Multiquip Ride-On Tandem Drum Rollers

A static roller for use on small asphalt paving jobs, driveways, bike paths and more when vibration is not required. This economy roller has been appreciated by contractors for more than half a century.

Features

• Hydrostatic transmission offers infinitely variable speed control for forward and reverse movement.
• Split from drum allows drum segments to turn independently during turns and avoids marring the asphalt.
• Two spring loaded steel scrapers provide constant tension and contact to keep the drums clean.
• Articulated from drum with automotive style steering.
• Large coated steel water tank for extended work.
• Economical chain drive.
• Use for small asphalt paving jobs such as driveways, bike paths, and for patching
• Can be used for granular sub-base soil compaction in preparation of asphalt paving.
• 8 HP Honda gasoline engine

Call For Freight Charge

Multiquip Whisperwatt Diesel Powered Generator DA7000SSA

The WhisperWatt series of diesel-powered generators has long been synonymous with superior performance and sound attenuation. As more job-sites and municipalities specify maximum sound levels, this generator is now the clear choice.

Features

• Compact, sound-attenuated package with full instrumentation, including hour meter and warning lights for oil, water and battery.
• Tier 4 Engine - ETA Compliant
• 7kW maximum, 6kW continuous
• 13.9 hp water-cooled Kubota diesel engine, 571 lb
• Sound-attenuated package keeps noise level to only 65.7dBA at 23 feet (6.9 meters)
• Brushless alternator design eliminates maintenance parts
• External drains for oil and fluids simplify maintenance
• Generator can be mounted on an optional wheel kit or trailer
• Liquid cooled Kubota diesel engine electric start

Multiquip MVHR60 Mikasa Plate Compactor

This 153-pound (69.6 kg) workhorse makes light work of even difficult soil compaction jobs.

• Simple, easy to use controls
• No mechanical plate shaft, minimizing maintenance
• Top cover keeps dirt off the engine
• Plate measures 13.75 x 18.9 inches (350 x 480 mm)
• Honda GX-120 motor
• 153 lb/69.4 kg
• 8.8 quart (8.3 liters) water tank capacity
• Can be purchased with or without water tank

DSGPULW Multiquip Duo Screed

The DuoScreed sports a unique blade profile that enables just one operator to quickly and accurately strike off concrete floors using a single blade for both form-to-form and wet screeding.

Multi-quip's DuoScreed utilizes a unique blade profile that enables one person to strike-off concrete floors.The screed's vibratory action embeds aggregate and reduces air voids, producing a strong dense slab, while eliminating the strenuous, time consuming labor of manual screeding

• Flexible drive shaft- Simple but durable power unit utilizes a maintenance-free flexible drive shaft
• Fingertip throttle control- Ergonomically designed to provide easy RPM adjustment
• Eight blade widths-Ranging from 6ft to 20 ft
• Lightweight blade construction- One-piece extruded aluminum, less than two pounds per linear foot
• Easy to use-Highly maneuverable around pipes or obstructions without marring slab surface
• Unique reversing blade-Power unit is easily rotated 180 degrees to allow form-to-form or wet screeding
• Adjustable control handle-Customizable for operator height and comfort and sports a convenient fingertip throttle control
• Portable design- The blade is quickly removed without tools; handles fold for storage
• Honda powered-Honda GX-35SAT 1.5hp four stroke gasoline engine
• DSB550 and DSB600 are a combination float and screed blade
• Power unit and screed blades are sold separately

Multiquip DA7000SSW Generator Options

• DA7000SSW Generator can be mounted on wheel kit or trailer
• Fits 7000 watts max. Kubota diesel engine Electric start DA7000SSW
• Trailer ships Free in the Continental US to Commercial Address
• Generator with optional trailer Length x width x height 53" x 33" x 34"

Multiquip GA Series Wheel Kits

Features

• UWK wheel kit fits all GA models except GA97HE
• WKT97 and WKT97C kit fit GA97HE model
• WKT97 2 pneumatic tires for job site mobility
• WKT97C 4 caster wheels for shop use

Multiquip 46" Power Trowels

Features a heavy-duty gearbox and spider assembly along with high-horsepower Honda engines.

• A 46" ring diameter
• 1-year warranty plus complete product service support for trowel's life
• Fully enclosed belt guard
• Includes lifting eye as standard equipment
• Optimal balance for smooth finishing
• Price includes standard style handle

Multiquip 6" MQ-62TDD Pumps
Deutz F2L2011 Diesel Engine
Multiquip offers three different trailer options for the MQ62TDD pump skid package. The first two options use our TRLRMP Multi-purpose trailer. One configuration uses the 16 gallon fuel cell that normally comes with the skid-mount MQ62TDD. The second configuration uses the multi-purpose trailer with the trailer’s 28 gallon fuel cell. The third option is the TRLR50XFP with a 41 gallon fuel cell for extended running times.

Features and benefits

• Multi-purpose: pumps trash, sewage, sludge, and runs well-points systems.
• Primes up to 25 ft.
• High performance 1,083 GPM (4,100 Lpm), Max head 100 ft, (31m)
• Automatic engine shutdown triggered by high oil temperature, low oil temperature, or V-belt breakage
• Volute and impeller are manufactured of cast iron for long life.
• Cast iron suction and discharge nipples, durable and easily replaced if threads are damaged.
• Electric start and low oil shutdown standard.
• Oil lubricated tungsten/carbide seals are standard for positive lubrication and maximum seal life.
• Wear resistant cast iron volute and impeller assure quick priming, minimal clogging, and optimum efficiency.
• Two-vane impeller easily handles up to 2" solids and debris.
• Balanced lifting bale

Multiquip Whiteman WBH-16EAWD All-Wheel Drive Power Buggies

Whiteman WBH-16 Series concrete and material handling power buggies from Multiquip are the most advanced dependable buggies on the market. Free shipping from Multiquip warehouse AWD greatly improve performance in sand, mud, loose gravel. Control switch allows operator to switch from two-wheel to all-wheel drive. Extra capacity 5.5 Gallon fuel tank for longer run times. Approx. Running Time 8 hours Infinitely variable, fully hydraulic drive system for smooth and steady operation. Removable Pneumatic tires for easy access to narrow work areas. Fully hydraulic dump can be controlled by a hand lever or foot pedal. Heavy-duty frame with low center of gravity Increased stability and traction 16 cubic ft polymer bucket for easy clean-up. Splash protection, a unique tub design reduces concrete splatter outside of bucket. Hydrostatic system provides enough power to fully supply both drive and dump functions simultaneously without slowing either. Heavy-duty frame with low center of gravity Increased stability and traction Riding platform locks in upright position for walk behind applications. Max payload 2500 lbs 6" dump height the most clearance in it's class; allows the operator to maneuver over forms. 18HP Vanguard Engine, top speed 7.25 mph. Ideal for landscaping applications, material sub-base distribution, job site cleanup and material transport. Forklift pockets for easy loading. Optional foam-filled tires provide additional traction and puncture resistance. Patented AWD allows quick change from standard drive to AWD.

Multiquip SP2 Series Push Gasoline Floor Saw

An exceptional performing saw for its size, the SP 2 is built to cover a wide range of cutting applications. This saw comes with a standard 20" Blade Guard to permit a 7-½" depth of cut.

Features

• The strong box type frame maintains its integrity providing smooth travel, superior diamond blade life and cutting performance.
• Standard features include: an adjustable height handle bar, lifting bail, removable hinged front blade guard, rugged front pointer, industrial blade shaft assembly, and 5 gallon built in water tank for dust control while cutting dry.
• Honda GX390 Gasoline Engine with Cyclone Air filtration standard.
• Adjustable handle bar with cushion grips.
• Cutting depth is 7.5 inches (190 mm)
• Hinged front, lift-up blade guard is designed to provide easy blade replacement.
• Locking ACME thread Raise/Lower.
• Water system provides an optimum flow and volume of water to the blade; uses standard hardware materials; provides easy replacement and facilitates routine maintenance practices.

Multiquip PS4030 Self-Propelled Pavement Saw

• Powerful 31 HP Deutz diesel engine, fully-enclosed self-lubricating blade shaft spindle assembly, an anti- vibration console design, and a maintenance-free propulsion system

Blade-shaft Spindle Assembly

• Blade Shaft and Support Bearing Assembly is fully enclosed in a dual sealed oil bathed design.
• 2-3/8" diameter shaft, precision engineered bearings.
• Machined cast iron housing.

• Maintenance free 12" x 3" Neoprene rear wheels and 8" x 3" Polyurethane front wheels.
• Over sized wheels promote easy to/from job site transit, accurate sawing, precise tracking and no more greasing.

• Independent Anti-Vibration console isolators.
• Reduced vibration to handlebars increases allowable operational time per OSHA specifications.
• Reduced injuries associated with lessened vibratory operating conditions.
• Component longevity of the saw is fully reached by minimizing overall operational harmonics.

• Hydraulic drive powered by a simple pump and motor design provides fore and aft propulsion (0 to 275 ft. per minute).
• Eliminates common gears, chains, sprockets and bearings associated with conventional drive systems.
• Benefit smooth and easy actuating control.

• 125 hour Blade Spindle Assembly and 500 hour Hydraulic System maintenance cycles.
• Increased operational time and Common lubricating fluids.

MultiQuip QP305SLT 3in High Pressure Centrifugal Dewatering Pump

The QP305SLT is our highest volume high pressure pump.
. Good for fire fighting and jetting applications and for moving up in those high-head jobs.

Features and benefits

• Pumps 145 gallons (549 liters) per minute.
• Maximum head of 328 feet (100 meters).
• Powered by a 9.5-hp, Honda gasoline engine
• Two 1-inch (25 mm) and one 1.5-inch (37 mm) discharge ports.
• Ports can be used independently or simultaneously depending on the application.
• Aluminum pump housing and impeller.
• Muffler is equipped with a spark arrester.
• Twin-impeller design: semi-open and a closed impeller.

Multiquip GA97HE twin-cylinder 18-hp Honda Engine Generator 9,700W

The generator for the toughest jobs it delivers enough power to run a variety of tools and equipment. Powered by a twin-cylinder engine with electric start, and recoil backup, it offers up to 10 hours of continuous run time.

Features:

• Twin duplex receptacles and three twist-lock receptacles for job site versatility
• 100% copper windings for maximum conductivity
• Alternator design eliminates maintenance by removing brushes and slip rings
• Runs for 10 hours on a full tank at full load
• Powered by a twin-cylinder Honda GX610 engine with low-oil shutdown, automatic idle control.
• Heavy-duty 1-inch (25 mm) steel pipe frame and shock mounts protect the generator
• Superior voltage regulation helps to keep tools and equipment running at optimal levels; helps them last longer.
• Includes folding lifting bale as standard equipment.
• Optional WKT97 Wheel Kit Available Item: 8054
• The best warranty in the industry, all GA-Series generators are covered by a two-year parts and labor warranty.
• Silent Type Muffler Reduces noise level.
• Voltmeter, this feature serves as a convenient diagnostic tool on the jobsite. The operator can quickly tell whether or not the generator is producing the correct voltage and prevent overheating of expensive tools and equipment.
• Mecc-Alte brushless alternator used on this model are manufactured to exacting specifications using the latest mass production methods.
• MQ Power generators use technology to control the voltage with a voltage variation less than 3% throughout the entire power range. That means you can use this generator with computers and sensitive electronics, safely, with no sacrifice in performance.
• This model is equiped with a Full Power Switch.

Multiquip PX400 2in Submersible Pump 110V

This submersible trash pump is ideal for debris-laden water and it's easy to transport to and from the job site.
With its plastic and stainless steel body, the pump is ideally designed for chemical applications such as fertilizers and salt water use.

Features and benefits

• Pumps solids up to 1-inch (25 mm) in diameter.
• A 2-inch (50 mm) discharge port.
• Pumping capacity of up to 72 gallons (273 liters) per minute.
• Plastic impeller, 304 stainless steel housing.
• Thermal overload protection, strain relief cord protection and side discharge.

Pramac S7500 MHHPI (Deluxe) Generator 7,500W

• Electric start with recoil back-up, frame mounted control panels & long run 8 gallon fuel tanks
• 12 V / 18 Amp lawn & garden battery required for electric start. Battery is not included.
• The Deluxe features a control panel with circuit breakers, main circuit breakers, hour-meter, voltmeter, 120V and 240V receptacles.
• Super heavy duty, yet compact, frames
• Quiet, reliable Honda GX390 13 -hp engine
• 12.1 hours runtime from 8 gallon fuel tank.
• Weight 200 lbs.
• The Deluxe series is a great choice for contractors, agriculture, roofers, masons, carpenters, disaster relief or anyone that needs quality power, reliable engines and no nonsense features.
• These are priced right compared to other generators and are a huge step up from the "big box" throw away units with inferior engines and sub par alternators.

Pramac Soundproof GSW65 D 50kW Deutz Diesel Generator Water Cooled

Suitable application is on construction sites, where durability and reliability are required to supply constant power to applications such as lighting, cranes, concrete mixers and conveyor belts. With low noise emissions, they are also suitable for open air activities, such as shows or sporting events.
Excellent performance and easily installed they can be used either to support main electricity failure or in any location off the grid "not connected" to the main power supply.

• Quiet internal residential muffler.
• Set easy to be transported with hand pallet truck.
• Central lifting point.
• Complete with engine and battery liquids.
• Oil draining pipe with cap.
• High capacity fuel tank for longer work without fuel refilling.
• This soundproof version is outfitted with access doors to simplify maintenance and repair operations.
• Deutz engines extremely high load acceptance capacity ensures instant electricity supply.
• They respond quickly to load fluctuations. In addition, the application will not suffer from frequency deviations.
• Highly efficient alternators.
• Constant supply guaranteed by the electronic voltage regulator under any generator operating condition.
• Engine service points are accessible from one side. The maintenance is easier through large doors.
• Rated capacity battery for immediate engine start.
• Genset protection under/over voltage, overload, battery charger failure, battery voltage out of limits, Automatic control panel mounted under/over frequency, start failure.
• EPA tier II compliant.

• Selector switch with six positions: Automatic test - Automatic starting - Engine locked - Mains contactor forced
• Manual starting * - Genset contactor forced.
• *Manual Starting: the preheating period begins automatically when this position is selected. It is necessary to select again this position to enable one more time the preheating period.
• Push-buttons: start/stop, up/down selection, reset.
• Emergency stop button.
• Remote starting availability.
• Automatic battery charger.
• Instrumentation: Generating set voltage - Generating set frequency - Generator set current - Battery voltage - Hours-meter - Mains voltage.

Pramac Soundproof GBL30 Deutz Diesel Oil Cooled

Suitable application is on construction sites, where durability and reliability are required to supply constant power to applications such as lighting, cranes, concrete mixers and conveyor belts. With low noise emissions, they are also suitable for open air activities, such as shows or sporting events.
Excellent performance and easily installed they can be used either to support main electricity failure or in any location off the grid "not connected" to the main power supply.

• Quiet internal residential muffler.
• Set easy to be transported with hand pallet truck.
• Central lifting point.
• Complete with engine and battery liquids.
• Oil draining pipe with cap.
• High capacity fuel tank for longer work without fuel refilling.
• This soundproof version is outfitted with access doors to simplify maintenance and repair operations.
• In oil cooled engines, the single fluid for both cooling and lubrication avoids corrosion and cavitations.
• Deutz engines extremely high load acceptance capacity ensures instant electricity supply.
• They respond quickly to load fluctuations. In addition, the application will not suffer from frequency deviations.
• Highly efficient alternators.
• Constant supply guaranteed by the electronic voltage regulator under any generator operating condition.
• Optical fuel level for an easier fuel check.
• Engine service points are accessible from one side. The maintenance is easier through large doors.
• Rated capacity battery for immediate engine start.
• Genset protection under/over voltage, overload, battery charger failure, battery voltage out of limits, Automatic control panel mounted under/over frequency, start failure.
• EPA tier II compliant.

• Selector switch with six positions: Automatic test - Automatic starting - Engine locked - Mains contactor forced
• Manual starting * - Genset contactor forced.
• *Manual Starting: the preheating period begins automatically when this position is selected. It is necessary to select again this position to enable one more time the preheating period.
• Push-buttons: start/stop, up/down selection, reset.
• Emergency stop button.
• Remote starting availability.
• Automatic battery charger.
• Instrumentation: Generating set voltage - Generating set frequency - Generator set current - Battery voltage - Hours-meter - Mains voltage.

Pramac Pi1700 Inverter Generator

• Limited Quantity Special Buy a Pramac Pi1700 Inverter Generator 1,650W and SAVE
• Pramac Pi1700 was $1039.50 now only $929.00
• The Pi1700 is portable and lightweight to carry which makes it convenient for power needs to run power tools, televisions, radios and etc. in remote locations. Boating is also another great idea where inverters come into play. The others are made to match applications where more power is needed.
• Weight 46.29 lb.
• 6 hours runtime @75%, from 0.92 gallon fuel tank
• Recoil starter system with electronic ignition makes for easy starting and reliable, consistent service
• Fully enclosed design for reduced sound output of 59 dB and protection
• Inverter technology reduces the overall size and weight by up to one third in comparison with similar class generators.
• Protected with built-in oil sensor that shuts off the ignition if the oil level drops too low
• Cast iron cylinder increases durability and extends engine performance
• Allows operations under an overload conditions up to 120% of the rated output for 20 seconds before output is cut off.
• This allows the starting of demanding loads such as air conditioners & compressors.
• Inverters are ideal for recreational, medical, standby and for powering equipment sensitive to voltage surges (eg. computers) which also gives the cleanest sine wave possible compared to all other generators.
• The sine wave is measured in THD or Total Harmonic Distortion.
• All Pramac products are exceptional in this category but the inverters are half that number to 3% Total Harmonic Distortion.

Pramac HL10E 540 20 In. X 45 In. Electric High-lift Pallet Jack

The HL10E 540 electric high-lift pallet jack feature infinitely adjustable height between the minimum and maximum level of 31-1/2"".
Perfect for skids, baskets and work applications.

Features and benefits

• Creating a useful workbench suitable for places like mechanical workshops.
• Can also be used to support other machines in production, picking and similar areas.
• One-piece ductile iron pump with airless and leak proof design.
• Pump has chrome plated piston. Included 2 stage hydraulic cylinder.
• Industrial grade high quality with 2 year manufacturer's warranty
• Weight Capacity in Pounds : 2200 Lbs.
• Handle length 32".
• Size 20"x48"
• All the controls (lowering / neutral / lifting) are available in a single lever for simple and safe control.
• Protective top cover made in ABS shock resistant plastic shielding the battery.
• Assembled Depth x Height x Width: 64.9 x 31.5 x 21.2 In.
• At a height of over 15", the rear stabilizers make a very safe and steady working platform, preventing rocking and movement in all directions.
• Weight 319 lbs.

Rubi DW-250-N Rail Saw

• Free Shipping from Rubi factory warehouse to a commercial address in the lower 48 states.
• Rips cuts 29" (with plunge) tile, diagonal cuts 20" x 20" tile,
• 1-1/2 hp direct drive motor with plunge cut capability
• 10" diamond blade included.
• 45 degree miter and plunge cutting features
• Removable legs for easy setup
• 10" Diamond blade, water pump, and 45 degree guide included
• Folding legs with built in wheels for mobility
• Weighs 84 lbs

QEP Brutus 24" Professional Tile Saw
Model 61024

• Free Fold-out stand with 3'' wheels, 10" diamond blade, side table & water pump
• Rip cuts tile 24" square, 18" diagonal
• Powerful 1.5 hp, 11.5 Amps, 3450 Rpm motor
• Weighs 106 lbs. w stand
• Size: 40†L x 21.5†W x 48.3†H (w/stand)
• Cutting table utilizes a slide tube mounting system for smooth, accurate cutting.
• Adjustable tilting head offers quick and easy 45° to 90° miter cuts.
• Automatic thermal overload protection prevents tile saw from overheating.
• Locking tilt-up blade guard makes blade changes quick and easy.
• Convenient stand with rear locking wheels keeps tile saw secure, and easily transportable.
• Rear and side water tray for water containment.
• 10" blade with standard 5/8" arbor
• Depth of cut: 3-1/8".
• Rust proof, fiberglass impregnated water tray easily slides in and out for easy cleaning.
• Large non-slip rubber matted table with pull-out extension to support large format tile and slabs.

Tile Master XL3 Plus High Production Tile Saw

Free shipping from factory warehouse Free 3pcs cutting package (a $49.99 value) Free Folding stand (a $84.99 value)

• Rip cut 31" tile, diagonally cuts 22" x 22" tile.
• Optional cart allows 34" rip cuts, 24" diagonal cuts.
• Saw is pictured with optional 24" diagonal cart.
• The sliding water pan allows instant adjustment from small to large material for unequaled productivity and convenience.
• New spring-assisted plunge cut capacity and blade shaft lock
• New galvanized water pan helps resist rust
• Free 10" diamond blade & water pump

• The saw features a galvanized pan which resists rusting. The saw features a new larger main cart and a standard extension for cutting large tile. The cam adjustment makes tensioning the belt simple, while the new optional adjustable rolling stand makes transporting the saw to and from the jobsite easier

Tilt-up Blade Guard
The heavy-duty cast aluminum guard provides maximum protection for the operator. Thicker water hose connects to the outside of the blade guard and evenly distributes water to both sides of the blade. This prevents the loss of blade side clearance, protecting the integrity of the blade for longer life and more accurate cuts. The wide blade guard prevents rubbing of profile wheels against the sides of the guard for reduced noise and easier wheel installation.

Aluminum Conveyor Cart Assembly and Extension
The cart is made of cast aluminum for strength and rigidity and includes a cast aluminum rip guide. The conveyor cart’s rubber top grips material securely for more accurate cuts. The large steel wheels help the cart roll smoothly on the tracks. A convenient ruler at the front is labeled both in inches and metric measurements.

Drive Belts
The Tile Master XL3 Plus features a premium, six-groove poly V-belt that drives the blade at the proper speed. V-belts have less vibration so they are smoother running, which also reduces belt slippage and transmits more power to the blade-shaft. The belt guard totally encloses the belt to protect both the operator and the saw components.

Other Features

Patented sliding tray design allows maximum cutting capacity on large tiles. The adjustable rolling stand has a patent-pending spring-assist for easy raising/lowering of saw. The cutting head can be adjusted to various heights Smooth rolling, large conveyor carts with metal wheels maintain high precision with fewer parts and less wear 10" blade capacity for cutting thicker material. Operator is able to cut 31" (787mm) square tiles in one pass and make diagonal cuts on tile up to 24" (609mm) square with optional cart. Choose rust-resistant galvanized pan or rust-proof stainless steel for easiest cleaning and maintenance. Ability to make spring-assisted plunge cuts. Bladeshaft lock makes blade removal easier. Features a 1-1/2 hp Baldor single voltage continuous-duty motor that is totally enclosed fan cooled (T.E.F.C.) and designed exclusively for Husqvarna. Feature a dual capacitor for increased power efficiency in low voltage starting conditions. Motors are UL and CSA approved. Water pump is epoxy-coated and lifetime lubricated. Water hoses connect easily to the outside of the blade guard.

FTS-150 Wet Saw Features

General Features

The FTS-150 meets the professional contractor’s needs. It makes rip cuts up to 19" and can diagonally cut 13" tiles. Blade capacity is from 6" to 10", including 6" profile wheels.

Heavy-Duty Water Pump

The premium grade, high output water pump provides maximum protection for diamond blades.

Bladeshaft Lock

The bladeshaft lock makes changing blades easy.

Tilt-up Blade Guard

The sturdy, cast aluminum blade guard pivots 90° for quick and easy blade changes. Designed to direct the flow of water to both sides of the blade, dual water tubes provide optimal cooling and extended blade life.

Cutting Accessories

Tile cutting accessories packaged with the saw include a rip guide, 90° protractor, dual 45° angle guide and a 45° bullnose miter guide. All have an innovative thumb-lock design which slides on and locks securely into place.

Conveyor Cart and Extension

Smooth roller design ensures accurate cuts. The injection-molded conveyor cart features a large surface area with grooves to drain water and debris away from the cut. It makes angled cuts faster and easier. The surface is textured, but not raised, preventing material from sliding. Inch and metric marks on the highly visible ruler aid in cutting tile to scale. The 5-1/2" x 16" extension is designed to attach on the side or front of the conveyor cart.

Heavy-Duty Water Pan and Frame

The heavy-duty water pan is injection molded and designed for easy removal. The welded steel frame has convenient handles on the front and back.

Folding Steel Stand with Wheels

Packaged with the saw, the steel stand features wheels with a one-touch brake set or release allowing for easy maneuverability.

Conveyor cart and 4pcs cutting package are plastic

Raimondi Gladiator Advance Wet Tile Saw

• Rip cut 41" tile, diagonally cut 29" x 29" tile
• 1.5HP, 110V belt driven motor
• Free Raimondi 10" diamond blade, 5/8" arbor
• Weighs 181 lbs
• Rail pivots to a variety of angles for a perfect miter cut
• Optional collapsible table extensions on both sides
• Legs fold into the bottom of the water pan for ease of transporting
• Cast and extruded aluminum framework.
• Easy-to-remove polypropylene tank for easy cleaning capacity 10 Gal.
• Extruded aluminum cutting tables are more accurate than bent stainless steel tables.
• Material lock-down bar and Collapsible table extensions are optional.
• Floating blade guard remains in contact with tile to provide extra safety.

Stow Trak 20 Masonry Saw

Powerful, rugged saws for clean, accurate cuts. When cutting brick, block, stone, slate or tile, Stow masonry saws perform to the highest of standards. Engineered for performance, the rigid design minimizes vibration. Designed for easy maintenance, these saws will last for years and continue to provide dependable and reliable service.

• Rugged oversize aluminum conveyor cart for maximum material stability and easy travel
• Classified as an industrial grade block saw, these models offer high production performance on job sites, building supply houses and brick/block plants.
• Stay-level blade guard for operator safety
• Rigid frame minimizes vibrations and assures accurate cutting
• Accurate screw thread and foot pedal control.
• 2 ways fork lift pockets.
• Ergonomic pull handle
• High volume water pump.
• Three phase motor available call for pricing.
• Dimensions 61"x25"x55"
• Blade not included

Alpha AWS-110 Electric Saw

• Water feed system included.
• 4-1/2", powerful 11 Amp motor. 20 mm Arbor.
• Using the guide provided you can work on the edge of the stone.
• Place a straight-edge on the stone and guide against it, or the AWS-110 can be used free hand like any other circular saw.
• For safety in-line Ground fault interrupter is included.

• Ideal for those working with natural and engineered stone, tile, concrete, masonry and glass.
• It was designed to produce straight and true cuts as required by professional fabricators and installers.
• Equipped with one of the most powerful motors in its class, the AWS-110 has the strength to power through hard dense materials, such as, porcelain, hard red granites and engineered stone.
• The water-feed supply eliminates the harmful dust particles common in dry cutting applications.
• The included self-stick felt strips can be applied to the base plate to protect the work surface from scratches. The AWS-110 may be used several ways.
• The reversible ruler guide down, one can work off the edge of the stone; in the up position, it can glide along a straight edge.
• Of course, it may be used free hand and either wet or dry.
• Additionally, utilizing the optional Carriage Assembly, one can use the Alpha® Guide Rail System to perform machine precision cuts.
• You can easily transition to polishing with the Alpha® WS120 polisher and Ceramica pads.
• The AWS-110 is more than a saw; it is a complete cutting system that can be used for cutting, scoring, profiling and more designed and manufactured with the highest quality standards, as are all Alpha Professional Tools® products.

Crain 820 Heavy Duty Undercut Saw

• 6-1/2†diameter carbide-tipped blade.
• Includes carrying case, hex wrench, and No. 805 Masonry blade for undercutting hearths.
• The saw undercuts walls, jambs, inside corners, and even most toe-spaces.
• It does it all - a real value for the price!
• Cuts masonry and fully undercuts most doors in place!

Porter Cable Tiger Saw Kit

• Variable Speed, Dual Action orbital for cutting in wood and reciprocating for cutting in metals.
• Quick-Change Blade Clamp, Blade can be installed upside down to allow better reach in tight fitting applications.
• Weight 9 lbs, 11.5 Amp motor delivers full 1-1/8" cutting stroke length .
• Heavy duty case, blade, manual.

D28755 DeWalt 14" Concrete Cut-Off Saw

• 14" Angle cutter, weight 24 lbs.
• 15 Amp motor provides power & speed for concrete cutting.
• Diamond blade not included.
• Epoxy coated field & armature provide long service life against abrasion from debris
• Soft start reduces reactionary torque during start up.
• Dust duct provides access to dust extraction while cutting concrete
• Dust sealed switch protects against dust ingestion for longer switch life
• Automatic turn-off shut down the tool when brushes need to be changed to avoid tool damage
• Adjustable guard for different cutting depths mounted at two points to maintain proper alignment
• Spindle lock button for fast, easy wheel changing
• Rotation directs sparks & debris towards the front of the tool & helps prevent climbing in the cut
• Great for builders, fire/rescue, maintenance, remodelers, roofers, masons, pipe fitters & many other applications
• Dust duct included!
• Tool length 21"
• 2 wire double insulated 'S' jacket rubber cord provides increased durability and life in hot and cold climates

• Wrench, masonry wheel, metal cutting wheel, integral dust duct.

Intertool Trac Star 2000 Stone Saw

Features

• Powerful 115 v, 18.8 Amp, 1-1/2 HP Heavy duty “washdown†motor.
• Produces a remarkable 4-1/2 ft. lbs of torque and carries a one year warranty.
• The blade revolves at 1725 rpm and won’t slow down, even when cutting 30 mm granite in one pass.
• The saw operates on a v-groove track and is AUTOMATICALLY drawn down the track with a variable speed, front wheel drive motor.
• Variable speed drive motor allows more efficient and effective cutting
• Operating under a constant pressure as it pulls the power unit down the trac.
• This assures the blade of no abrupt jerks into the stone as it cuts and results in a perfect, straight cut with no saw marks on the vertical edge.
• A standard 8†blade will cut 2-1/4†stone, 7†blade will cut up to 1-3/4†and a 10†blade will cut 3-1/4â€.
• Fast. Accurate. Portable. Automatic.

Pearl Abrasive Water Kit for Circular Saws

Includes: Ground Fault Circuit Interrupter, ball valve diverter assembly, Quick Release Coupler with 2 Rubber Gaskets, Flexible Plastic Tube, Plastic Nut, Hose Clamps.

• Reduces the operator’s levels of dangerous, cancer causing airborne pathogens, dust and fatigue!
• Finger tip controls allow the minimal use of water, to help control the hazards to the environment created by dry cutting.
• Cooling and lubricating with water will make your expensive diamond blades last up to 50% longer.
• Cooling the blade also helps to cool the motor, thus extending the life of your saw.
• Kit includes a UL Listed Ground Fault Circuit Interrupter to eliminate shock hazard.
• Blade Roller & Saw not included

Pearl Sidewinder Blade Roller

• Removable rolling carriage for left or right circular saws
• Increase cutting speed
• Make straight cuts
• Easily increase control & accuracy
• No Tools Required
• Non-Marking Wheels
• Eliminate Costly Heavy Equipment

• Cutting concrete slab, marble, granite, Wonder Board, plywood, stucco
• Making tension relief lines in slab concrete
• Creating access cuts in slab concrete for plumbing and electrical retrofit
• Scoring decorative lines in poured slab or overlays
• Fabricating slab granite and marble countertops, floors, etc
• Ripping long straight cuts on plywood sheeting
• Creating cutouts in stucco for retro fitting doors and windows

• Makita 5007NH
• Makita 5007NL
• Makita 5007NB
• Dewalt DW368
• Porter Cable 743
• Milwaukee 6390
• Bosch 1655

Buy a 10" Pearl Specialist blade and save Pearl 10" Specialist was $61.49 now only $55.00 Pearl DTL Series B28 professional Bronze Bonded Wet Diamond Blade

• Our DTL’s have a continuous rim for a clean, chip-free cut.
• Cut tile, ceramic tile, marble, soft Stone & porcelain.
• Bronze Bonded for better performance.
• 5/8" arbor
• .060 thickness

Pearl SHD Dry Cutting Porcelain & Granite Blade

Great performance blade on very hard materials! Using this premium product will result in a cool, clean, chip-free cut.

• Dry cutting, turbo rim blade for clean, chip-free cutting on porcelain.
• Available in 4" & 4-1/2" sizes.
• 4" blade 20mm, 5/8 arbor
• 4-1/2" blade 7/8, 5/8 arbor
• SHD SERIES PORCELAIN/GRANITE DRY - Extra Hard Materials. Porcelain, Granite and Hard Stone.
• Great performance blade on very hard materials!

Buy a Pearl SD Dry Cutting Turbo Diamond Blade and SavePearl SD Dry Cutting Turbo Diamond Blade

• Cuts granite, block, brick, concrete marble, natural stone, refractory material, soft stone, sand stone.
• Wave design features add stability to the steel core, thus eliminating warping problems.
• The waved-core allows air to be drawn in through the matrix and across the core, reducing friction keeping the core cool.
• While the blade is cutting, the debris is removed from the cutting path via the waved core thus extending the life of the blade.
• 4" blade 20mm, 5/8 arbors
• 4-1/2" blades have a: 7/8 / 5/8 arbors
• 7" blades have a: DM / 7/8 / 5/8 arbors

Pearl SD Gold Dry Cutting Turbo Diamond Blade

• Cuts granite, block, brick, concrete marble, natural stone, refractory material, soft stone, sand stone.
• Wave design features add stability to the steel core, thus eliminating warping problems.
• The waved-core allows air to be drawn in through the matrix and across the core, reducing friction keeping the core cool.
• While the blade is cutting, the debris is removed from the cutting path via the waved core thus extending the life of the blade.
• 4" blade 20mm, 5/8 arbors
• 4-1/2" blades have a: 7/8 / 5/8 arbors
• 7" blades have a: DM / 7/8 / 5/8 arbors

Pearl Pro-V Double Row Cup Wheel

• 4" and 7" Double Row Segmented Diamond Cup Wheel
• For fast grinding, mark removal, de-burring, rough surface grinding
• Produces less dust and is more productive than abrasives
• Buy 2 pieces get 20% off

Pearl tradition of professional quality a general purpose masonry blade that can handle most anything you throw at it.

• Laser welded bond ensures safety and durability.
• Segment and U-Gullet designs promote fast cutting on brick, block and stone while keeping the core cool.
• 10mm diamond height. Wet or Dry Use.
• Specs: 14x125, 1" arbor
• Max RPM 5,400
• Use on: Block, Brick, Paver Brick, Hard Brick,Masonry, Natural Stone, Refractory Material, Roof Tile, Artificial Stone, Sandstone, Soft Stone, Stone

Makita HR1830F Features

• Dual operation mode; rotation only and hammering with rotation
• Variable speed (0-1,500 Rpm) and (0-5,000 BPM) for demanding applications
• No hammering when idling function ensures extra-low vibration under no load
• L.E.D. light illuminates drilling surface for more accurate work.
• Soft-grip side handle with elastomer for better comfort
• Ideal for overhead applications and working in confined areas
• Carbon brushes for extended service life
• Ergonomic and well-balanced design (3.7 lbs.)
• Recessed lock-on button for continuous use

Makita HK0500 SDS+ Power Scraper

• Variable speed, SDS-Plus, Weight: 6.8 pounds
• Lightweight and easy to handle
• Compact and comfortable design
• Features a one-touch sliding chuck for easy bit installation and removal.
• Large and comfortable trigger switch and variable speed control dial.
• 5.0 amps: 115 Volts; 2,000– 3,500 BPM;
• Includes 1-1/2" x 8" chisel and plastic case.
• The HK0500 Power Scraper (SDS) from Makita has a compact portable design that is excellent for removing tile and mortar.
• A specially designed small diameter barrel for easy gripping and a large one touch sliding chuck for easy bit installation and removal.
• Powerful 5 amp. motor delivers 2,000-3,500 BPM for maximum performance. The 12 position bit adjustment allows for the scrapper blade to be easily positioned without removing from the chuck.
• Product Dimensions: 19 x 14 x 6 inches

  

  SDS-PLUS Shank

  

Makita HM1100C 13.5LB Demo Hammer SDS Max.

• Weight 14 lbs.
• 11 AMPS. 20-5/8" Long.
• 1300-2650 blows per minute.
• Plastic Carrying case included.
• Chisel not Included.
• SDS-Max technology gives you a more precise impact and reduced friction for increased tool life.

SDS-MAX Shank

Makita 4-1/2" Variable Speed Angle Grinder

• For sanding, polishing, and grinding applications.
• 12 Amp, weight 4 lbs. 5/8"-11 spindle thread.
• Variable speed 2,800 to 10,500 Rpm.
• SJS prevents tool kickback caused by accidental wheel binding.
• Labyrinth construction seals motor and bearings from dust.

Powerful 2.5 hp Robin, 85cc, Overhead Valve (OHV) engine

1,100 Watt maximum output Weight 55 lb. 4.2 hours runtime from 1.1 gallon fuel tank Recoil starter system with electronic ignition makes for easy starting and reliable, consistent service Fully enclosed design for reduced sound output of 59 dB and protection Innovative cooling design with large cooling fins engineered into the crankcase, cylinder and mounting base Protected with built-in oil sensor that shuts off the ignition if the oil level drops too low Cast iron cylinder increases durability and extends engine performance Large, heavy duty air and fuel filters with high capacity to reduce service intervals Impact resistant design

Specifications:

Max. Output Current: 1,100W/9.2A Length 19-1/2'', Width 11-3/4'', Height 17-1/2''

Buy a HM1810 Makita 70 lbs Demolition Hammer and save Makita HM1810 was $1404.00 now $1352.99 New More Powerful 70 lbs. Breaker Hammer has 3X Less Vibration

• Free hammer cart and 4 bits
• Counterbalance system reduces vibration to only 8 m/s² for unmatched comfort.
• Powerful 15 Amp motor; efficient 1,100 BPM to tackle the most demanding jobs.
• Accepts popular 1-1/8" hex hammer steel.
• Automatic brush cut-out system protects commutator for longer tool life.
• 16.4 ft. jobsite cord for greater versatility and instant power.
• Cylindrical tool holder enables new bolt holes to be drilled should the original bolts break.
• Warning lamp indicates trouble with the cord; AC/DC switch for use with alternative power sources
• Large, easy to operate switch for operator comfort and control
• Lowest noise level in its class at only 107 dB.
• Vibration Level: 8 m/s²
• Cord Length: 16.4 ft.
• Tool length: 32-1/2"

1-1/8" Pavement Breakers Shank

Makita Cut-Off Saw

General Features

• Buy a 14" saw now and receive a FREE 14" masonry blade
• Five-stage, foam-paper-nylon system with Advanced Directional Air Flow provides very clean air for better saw performance
• Reinforced aluminum blade guard with 70 degrees range of limitless positioning using a marked knob handle
• Improved ignition system with larger flywheel and rare earth magnets for more power
• Cutting arm position simply changes from center position to flush (outboard) position allowing cuts directly adjacent to curb edges, walls or directly above the ground
• Starter grip and decompression valve located on the same side for faster starting
• On-Off-Choke operating switch on a single lever for operator convenience
• Cushioned operator grips with 4 vibration-absorption rubber buffers for increased operator comfort
• Water kit is assembled to saw and can be used with garden hose, gravity tank or pressure tank
• Improved exhaust emissions are EPA Phase II compliant while maintaining power and performance
• 50-1 Fuel Mixture, 37oz fuel tank Capacity
• Includes 12", 14", or 16" abrasive wheel, water kit, 2 wrenches, screwdriver
• Shown with optional diamond blade.

G12010R Makita Generator 12,000W

High Output Capacity for Demanding Situations

G12010R Makita Generator Features:

• Feature OSHA approved receptables
• Commercial-duty steel gas tank
• All ball bearing supported, forged steel crankshaft
• Cast-in-place cylinder liner made from high carbon steel
• Water resistant louvers (IP235 rating) to protect the electrical components
• Bubber feet/mounts to reduce vibration
• 8+ hours of operation from a full fuel tank
• Electronic voltage regulator for more accurate voltage output
• Fuel gauge for easy monitoring
• GFCI safety receptacle & USDA approved spark arresting muffler
• Dual voltage - 120V/240V output
• Electric starter with automatic choke
• Automatic idle control reduces engine to low RPM operation during no load draws, reducing fuel consumption & engine wear
• Tool kit & 2 each Ignition key

Technical Features

Makita Cordless Rebar Cutter SC190DWDE

• Specifically Designed to Cut 1/8" to 3/4" Rebar
• Powered by 18V (2.6Ah) Nickel-Metal Hydride battery.
• Fast and effortless cutting speed in only 6 seconds.
• Specifically designed to cut rebar and various steel rod.
• Fast and easy replacement of shear blades.
• Head rotates 360° for different cutting positions.
• Weight only 23 lbs. (w battery)
• Ergonomic pistol grip handle for operator comfort and control
• "TCT" total control variable speed trigger.
• Push button forward/reverse button for one-handed operation.
• External oil port for easy maintenance.
• Externally accessible brushes for extended tool life.
• Battery 2.6 (Ah).
• Watt Hours 46.8
• Length 16-3/8"

• 2 Ea. Ni-MH Battery 1834 (193159-1)
• Hex wrench 3, Hex wrench 4, Hex wrench 5, Hex wrench 6, Hex wrench 17-19.
• Charger DC1801
• Battery cover (414938-7)
• Cutter blade Set.
• Plastic tool case (SC08100920)

Makita PC1100 Concrete Planer Diamond Wheels

• For use with Makita PC1100 Concrete Planer
• Use Makita 792289-1 diamond wheel for a smooth finish
• Use Makita 724907-1A diamond wheel for fast material removal

5″ Bosch 1773AK Concrete Surfacing Grinder

• Exclusive Dust Protection System
• Perfect for concrete surfacing such as de-burring and refurbishing
• Also ideal for smoothing floor pavement and removing graffiti, weather worn paint

• Lock-on/off switch For extended use applications
• Double sealed ball bearings and two "lip-sealing" protective rings Added protection against dust contamination
• Constant ResponseTM Circuitry Provides soft-start, maintains constant speed under load, provides overload protection
• Automatic restart protection Protects against automatic restart after a power failure. Ensures that tool is intentionally powered on each time.
• Sealed switch Keeps debris out of the switch mechanism and extends switch life
• Service MinderTM light Indicates when preventative maintenance is required
• 5/8"-11 spindle Wide flexibility for mounting most popular accessories
• Epoxy coated field windings Provides ultimate protection against abrasive dust and debris
• Wrap around auxiliary handle For easy handling
• Spindle lock For quick wheel changes
• Double Insulated, UL listed, complies to OSHA

• Auxiliary Handle
• Flange Kit
• Spanner Wrench
• 5" Diamond Cup Wheel DC510
• Vacuum Adapter VAC002
• Extra Brush Rings
• Carrying Case

Bosch 11536VSR 36V 1″ SDS-Plus Rotary Hammer

• Drills faster than key competitors, both corded and cordless!
• 50% Faster Drilling - 7.1 in/minute!
• 1″ solid bit capacity
• 2.5″ core bit capacity
• 3-Mode Selector Rotation only, rotary hammer and hammer only mode
• Impact Force - 2.2ft.-lbs.
• Litheonâ„¢ 36V batteries Allows more battery charges, longer run time and more power.
• SDS-Plus® Bit System
• Variable Speed Reversing Trigger
• Vario-Lockâ„¢ Positioning Rotates and Locks chisel into 36 different positions
• Tool-free bit changes with automatic bit locking, dust protection and maximum impact energy transfer rate
• Litheonâ„¢ Fast Charger Charges 36V batteries to 80% of capacity in 30 minutes
• Integral Clutch helps minimize torque reaction

• Impact Energy 2.2 (ft. lbs.)
• No Load 0-960 RPM
• No Load 0-4,260 BPM
• Length 15″
• Weight 9.6 lbs
• Max. Capacity in Concrete 1″
• Max. Capacity in Wood 1-1/4″
• Max. Capacity in Metal 1/2″

Laser Fusion blades with exclusive progressive segment spacing, every fifth segment is raised for more aggressive cutting

Bosch SpeedWave Segmented Masonry Blade

• Large 10mm diamond rim height
• For fast cutting of brick, block, concrete, block, brick, steel, marble, natural stone, refractory material, soft stone, and sand stone
• Can be used with angle grinders, worm-drive saws, and circular saws
• Wet/Dry cutting
• Strong Steel Core .080"
• Standard 7/8", 5/8" Arbor

Patented Laser Fusion blades set the Bosch line apart from the competition. Exclusive process uses a precision laser application to fuse a proprietary mix of diamonds and metal bonding material directly to the steel blade core. This unsurpassed bonding delivers superior diamond retention and distribution along with greatly increased cutting speeds up to 30% faster than standard blades in the same price range. Cuts are consistently cleaner and blade life is ultimately maximized.

Target By Husqvarna Solo Trac Grinder

With its small, compact design, the Solo Trac RG 1112 is a powerful and productive grinder ideal for grinding smaller areas and leveling uneven joints

Free shipping from factory warehouse

Grinds Surfaces Such As

• Brick
• Ceramic tile floors
• Concrete slabs
• Stone
• Terrazzo

• Grinds or cleans concrete and terrazzo surfaces
• Levels uneven joints
• Removes epoxies, high spots, mastics, thin-set and urethanes

• 12" working width
• Large diameter wheels allow for easy mobility
• Tapered front provides excellent visibility of the work surface
• Adjustable handle for operator comfort
• Can use 10" and 12" grinding discs
• Only "TDGH type" grinding heads can be used.

Flex L3410VR 5" Variable Speed Grinder.

• 11 Amp, Motor, 3,000 to 11,000 Rpm.
• Soft-vibe handle for reduced vibration.
• 4.1 lbs. 5/8"-11 Spindle thread,
• Soft start, Rpm pre-set dial.
• FLEX Six-fold microprocessor electronics: Speed selection, consistent speed control by tachometer generator, soft start, restart protection after power interruption, overload protection, and temperature monitoring.

Metabo 1-1/8" SDS Plus Rotary Hammer

• Buy a Metabo KHE-D 28 1" SDS Plus Rotary Hammer now and save Offer good while supplies last
• Metabo KHE-D 1" SDS Plus Rotary Hammer was $320.99 now only $260.00
• Hammer stop
• Rotation stop
• Clockwise and anticlockwise rotation
• Metabo "Quick" drill chuck change
• Vario Tacho Constamatic (VTC) full-wave electronics
• Robust Metabo Marathon motor
• Pneumatic high-performance hammer mechanism
• Die cast aluminum gear housing
• Ergonomic housing design for fatigue-proof operation
• Rubber-coated handle
• Comfortable operation and safety through auxiliary handle
• Rubber coated additional handle with drill depth-stop
• Metabo S-automatic torque limiting clutch
• Metabo winding protection grid
• No-volt release switch
• Auto-stop carbon brushes
• Brush wear indicator

• Rated input power 1010 watts
• Tool Weight 8.1 lbs

All Metabo tools are covered by a 3 year warranty by registering your product online on the metabo website

Metabo WE9-125 5" Variable Speed Grinder

• Grinding disc diameter 5"
• Variable Speed Control- 3,000-10,000 Rpm'S
• Torque 22 in-lbs
• Weight 4.2 lbs
• Thumbwheel for preselection of speed

The WE14-125 VS 5" Angle Grinder is ideal for both grinding and cutting stone when on full speed, and can also be dialed down to low speed for stone finishing and polishin. 7.5 Amp motor, with special winding protection that prevents damage from dust for longer motor life Disc speed is variable from 3,000 to 10,000 Rpm (no-load) Vario Tacho Constamatic (VTC) electronics provide speed stabilization under load for efficient material removal. Maximum torque is 29 inch-lbs The grinder features Metabo’s “Quick†wheel change system, enabling rapid tool-less changes for increased productivity Additional VibraTech handle for vibration damping Wheel guard can be adjusted without tools, allowing operators to quickly shift from grinding to cutting Featuring Metabo S automatic safety clutch, which prevents sudden reverse torque in the event of a jam Electronic thermal overload protection shuts down the tool if it gets too hot while operating at reduced speeds, which can cause increased temperatures The grinder also features current interruption protection, a spindle lock, a low profile aluminum die cast gear housing, an electronic winding temperature monitor with LED display, and auto-stop carbon brushes All Metabo tools are covered by a 3 year warranty by registering your product online on the metabo website

Edco Four-Disc Grinder

EDCO Grinders - Proven in over 40 years of use. Accept no substitute!

Dimensions:

• Length 49" x Width 40"

• 36" Working width has 4 square feet of surface contact

• 4-Multi accessory disc, 3" vacuum port & water port
• Electric 5 hp 230 Volts Single Phase motor.
• Propane 11 hp 115 Volts starter.

• Gas, electric or propane power sources available
• Includes 4 multi-accessory discs that accept Dyma-Serts, Strip-Serts and all other grinder accessories
• 4 counter rotating discs are double neoprene mounted for smooth, even action
• Fast controlled grinding for larger areas
• 12-Grinding insert accessories per loading

• Production grinding and floor cleaning on large surface areas such as airports, warehouses, parking decks, manufacturing plants, malls and sports arenas.

Edco Traffic Line Remover

Remove traffic lines from asphalt or concrete – and get the job done quickly!

EDCO's easy-to-use Traffic Line Remover can be pushed or pulled by one person in congested or limited access areas such as city streets, crosswalks and school safety zones.

Move the unit side to side for feathered-edge patterns that weather quickly and blend with the undisturbed road surface.

Production Rate:

• 7" Working width will grind approximately 700-1000 lineal ft per hour with Edco TLR Carbide Cutters
• Length 46-1/2", Width 29"

• 3-24 Bit carbide cutter assemblies

• 3-Carbide cutter bit assemblies

• Removing traffic lines and markings
• Removing painted and thermoplastic lines

Edco 250 CFM Vacuum

Edco 500 CFM Vacuum

Edco 8 hp PAC-8 Air Compressor

8 HP 16.2 CFM @ 100 PSI Air Compressor with Low Oil Shutdown

• Heavy-Duty two stage pump with cast iron cylinder, cast aluminum head and 62 oz. crankcase pre-filled with oil
• Heavy-Duty 2 piece, 16 gauge bolted belt guard
• Pilot valve unloading system with aluminum manifold
• Metal intake filter/silencer with replaceable element
• Automatic engine idle for economy and long service life
• Extra heavy-duty tank assembly with 9 gallon capacity
• Oil drain extensions on pump and engine
• Fully pneumatic/steel hub wheels
• 7 gauge steel construction
• Stainless steel reed valves
• Schmidt belt tightening device
• Flexible braided discharge line
• Automotive style bearing inserts

Edco 46" Power Trowels

Rugged, dependable EDCO Power Trowels save contractors time, labor and money.

• Precision engineered gearboxes and spider assemblies for long, trouble free life.
• High strength steel handles with belly bar provide maximum comfort and control.

Edco 24" Power Trowels

Edco 12" Self-Propelled Scarifier

With a working width to 12", the CPU-12 is for high production use in industrial plants, malls, dairy barns, roads or warehouses.

Features

• Up to 12" working width (30 cm.)
• 1,250-1,500 sq. ft./hr - (116-139 sq. m./hr) at a depth of 1/8" (3 mm.)
• Adjustable to 1/4" working depth per pass (6 mm.)
• Accommodates EDCO's largest cutters for longer life and more removal
• Electric 3 Phase 230/460 Volts.
• 38 HP Gasoline Wisconsin

• Planing concrete, asphalt and epoxies elastomerics and masterplate floors with ease
• High production use in industrial plants, malls, dairy barns, warehouses and on roads

• Up-cut drum rotation and heavyweight construction provide faster milling action and more uniform surface texture
• Hydraulic-powered engage/disengage lever lowers or raises drum from surface
• Standard Outrigger Axle Assembly enables the machine to follow slab contours closely when working on uneven surfaces and provide uniform surface removal
• Hydrostatic drive transmission provides a smooth forward & reverse speed control and less operator fatigue
• Cam-operated fifth wheel allows the operator to change direction or reposition the machine while the engine is still running
• Dimensions: Length 53", Width 36", 43" Height.

• A propane kit is available for the CPU-12

Edco 10" Diamond Discs

Use with Edco 10" Turbo Grinder The 10" Turbo Grinder works 4 to 5 times faster than conventional floor grinders and are designed for high production. The life expectancy of a disc depends on the material being removed. The discs can be used wet or dry.

• Red Disc General Purpose Concrete
• White Disc Abrasive Green/General Purpose Concrete
• Green Disc Green Concrete
• Blue Disc Fine Grinding
• Gold Disc Very Fine Grinding
• Silver Disc Economy Disc 10 and 20 Segmented Discs Available

Wet Porcelain Drilling Kit In Case:

Kit Includes:

• 6 diamond bits Ø 1", 1-3/8", 1-3/4", 2", 2-1/2", 3".
• 1 universal drilling guide with suction cup
• Tested and approved by our team.

Tomecanic Astro 800 Electic Tile Cutter

Buy a Tomecanic Astro while supplies last and SAVE Tomecanic Astro was $164.99 now only $139.99 Free shock-proof case, two 200 mm (8") diamond blades (one turbo, one continuous rim) included.

General Information

• Stainless steel cutting table with water recovery system.
• Only weighs 27-1/2 lbs, (12.5 kg)
• Thermal overload switch
• Cuts Porcelain, ceramic, glass, tiles, marble, and other materials
• Includes shock-proof case, two 8" (200 mm) diamond blades (one turbo, one continuous rim).
• Tilt-up Table for mitering up to 13-1/3" (334 cm) tile
• Tile Saw features a flat, open-table design as well as a large work surface for high visibility.
• Adjustment knobs lock the guide in place to ensure parallel alignment to the blade.

PTC Carbide Porcelain Tile Cutter.

• Easy Start up and rapid penetration in Porcelain tile.
• Special carbide tip ensures accurate holes and virtually eliminates drill bit wander.
• Max operating speed, is between 700 and 900 Rpm.
• Spray water on the PTC bit when drilling, to keep the bit cool and sharp.
• Renewing tip geometry, when the products life is exhausted in Porcelain, the PTC bit can be used in softer materials.
• Holes can be drilled in as little as 20 seconds
• Contains One PTC Carbide Bit and One masonry bit of the same size.
• Packaged in a clear plastic tube with instructions.
• The PTC 1/4" carbide bit is also used to drill a pilot hole necessary for use with the PTC water feed adapter and PTC2 Diamond Crowns.
• Made in the UK.

Wet Diamond Coring Bit

• Excellent for drilling in granite and porcelain
• 5/8" thread female arbor, fit all wet polishers
• Use wet only, operating speed is between 1800 and 2500 rpm.
• Fits most wet polisher.

Armeg PTC2 Diamond Porcelain Crown Bit.

The solution to durability and extended life: Thin wall, continuous diamond crowns for fast, efficient cutting and extended life. Not to be confused with some short life diamond grit alternatives.

• Thin wall, continuous diamond crowns for fast, efficient cutting and extended life.
• Max operating speed, is between 700 and 900 Rpm.
• Perfect combination of diamond grade and precision manufacturing, provides exceptional products strength and greatly enhanced tool life.
• Drive adapter incorporate a water delivery system for crown cooling.
• Anchor and fasten holes for small plugs and anchors.
• Drill water pipes, shower heads & faucets, drain pipes & toilet drain pipe.
• Bits must be used with water adapters small diameter use with 3/16" to 3/8" crowns large diameter water adapter use with 1/2" to 4-1/2" crowns
• Made in the UK.

• 3/16" Continuous diamond crown matrix expose a new cutting surface while drilling for faster cuts and longer life.
• Unique profile produces very accurate and neat holes with minimal entry and exit damage.
• Specially designed diamond crown construction reduces drag and allows for easy tile slug removal.
• Life expectancy of the Diamond Crown is 350+ holes in Porcelain tile with proper usage.
• Holes can be drilled in less than 2 minutes.
• The PTC2 Diamond Crown must be used with a PTC water feed adapter.
• Maximum depth of cut: 3/4".
• Water swivel sold separately, see item 9562

Armeg PTC 1-3/8in Diamond Crown Bit Starter Kit

• This handy starter kit comes with everything needed to complete the drilling of porcelain tile
• Starter kits include 1-3/8" PTC diamond crown bit, PTC carbide 1/4" pilot drill, 1/4" professional masonry drill, water fed adaptor, water feed tube and nozzle, & water feed clamp.

CST Berger Lasermark LM54
Interior-Exterior Multi-Line Laser Cross with Down Plumb, Self-Leveling

• 4 Laser-crosses at 90° to each other
• Laser-cross to the ceiling
• Plumb down beam to the floor
• Select 4 visible laser lines individually
• Solid magnetic dampening
• Adjustable 360° circle reading
• Tangent screw—for fine tune adjustment
• Compensator-lock for transport
• Visible alarm when out of level
• Use with floor trivet, removable, also mount to 5/8-11 thread
• Battery life 30 hrs.
• Water and dust proof.
• Exterior kit includes LLD-20 laser line detector.

CST Berger LM800

Dual-Beam with Self-Leveling in Horizontal, Vertical, and Plumb!

LM800 is the ultimate designed dual beam, dual slope rotary laser with horizontal and vertical self-leveling and many features to make the instrument ideal for all indoor and outdoor jobs. The LM800 is ideal for outdoor leveling and grading jobs with dual-slope capability up to 10%.

Features

• Scanning feature preset angles of 0, 10, 45, 90 and 180 degree to increase beam visibility
• Variable speed rotation for maximum visibility in any light condition-0, 150, 300, and 600 Rpm
• Clock-wise and CCW head positioning for fast and easy alignment in vertical/horizontal applications
• Three beams-horizontal beam, up plumb and down plumb beams
• Automatic / Manuel mode
• Anti-drift system
• Wide self-leveling range of +/- 5 degree
• Low battery indicator
• Heavy duty glass enclosed beacon and durable sealed housing is water and dust-proof (IPX57) to ensure years of dependable operation
• Pro-grade - Motorized, Electronic horizontal and vertical self-leveling
• 5/8-11 tripod Threads on base as well as handle for horizontal and vertical mounting

LM800I : LM 800 Interior package, w/ plumb down beam includes v-mount, remote, 2 targets, Ni-MH, charger kit, case, glasses.
LM800DI : LM800 Interior package w/detector. Includes same above plus LD400 Laser detector.
LM800PKG : LM800 Complete package, includes same as LM800DI plus aluminum tripod and rod.

All include hard-shell carrying case and instruction manual

CST Berger LM800-GR

• Automatic/Manual mode
• Anti-drift system
• Wide Self-Leveling Range of +/-5 degree
• Low battery indicator
• Heavy duty glass enclosed beacon and durable sealed housing is water and dust-proof (IPX57) to ensure years of dependable operation
• Grade capability : dual-slope up to +/- 10%

All include instruction manual

CST Berger Lasermark LM1000X Rotary Laser

For the contractor who needs optimum versatility and affordable price, the LM1000X is the laser of choice. Its bright red beam and variable rotation speed offer the flexibility of use with or without a detector for interior and outdoor work.

Automatic self-leveling pendulum dual-beam rotary lasers

• Scanning feature preset angles of 0, 10, 45, 90, and 180 degree
• Variable speed rotation : 0, 150, 300, and 600 Rpm
• Its bright red beam and variable rotation speed offer the flexibility of use with or without a detector for interior and outdoor work.
• Scanning Feature Preset Angles to Increase Beam Visibility
• Variable Speed Rotation for Maximum Visibility
• Clock-wise and CCW Head Positioning for Fast and Easy Alignment in Vertical/Horizontal Applications
• Dual Beams– Horizontal Beam and Up Plumb Beam
• Vertical Lay-down self-leveling in both horizontal and vertical position
• Wide Electronic Self-Leveling Range of ±5º
• Low Battery Indicator
• Heavy Duty Glass Enclosed Beacon and Durable Sealed Housing is Water and Dust-Proof to Ensure Years of Dependable Operation
• Automatic / Manual Mode– Allow instrument to be placed in any position (to grade)

LM1000X: LM1000X rotary laser, includes remote, target, glasses, v-mount, LD120 detector, Ni-MH Battery/Charger.
LM1000XE: LM1000X rotary laser, includes remote, LD120 detector, Ni-MH Battery/Charger, alum. tripod, rod.

CST Berger LT-160 True Laser Measurer

• Includes: Batteries, Pouch, and User’s Manual
• Measure at the speed of light– leading edge technology
• 3 Line Illuminated LCD Display
• Feet/ Tenths/ Inch/ Metric Readings
• Calculate Area/ Volume
• Stake Out Function
• Min/Max Distance Tracking
• Timed Readings
• Historical Memory - 10 inputs
• Accurate 3-Line Pythagoras Function
• Audible Measurement Indicator
• Powered by 2 “AAA†batteries
• Warranty: Two Years

• Laser Output: 635nm, Class II
• Accuracy: Up to ±1/16" (±1.5mm)
• Range: Up to 195' (60m)
• Environment: Water and dust resistant (IP54)

Stanley Fat Max Tru Laser Measurer 100 Series.
Model TLM 100

• Fast, accurate, and easy to measure-just point and shoot.
• Simple design and easy push button operation
• Quicker and easier to use than traditional tape measurers and more accurate than sonic style measuring devices.
• Large LCD screen and ergonomic rubberized grip for comfort and impact resistance.
• Just aim, push the button, and measure.
• The TLM100 is able to calculate distance, area and volume and accurate to ±1/4-in per 100-ft. with a range of 100-ft.
• Able to measure indoors, outdoors and hard to reach spots such as vertical distances.
• Safer than other methods; avoid hazardous measuring procedures and measure safely.
• Increase your level of professionalism, with a lightweight, portable measuring device.
• Measuring Accuracy is 1/4" at 100 Ft.
• Single Point and Push ON/Measurement
• Measuring Features include Distance, Area, Volume and Calculator.

18V Cordless Rotary Laser Kit With Digital Detector & Clamp (Exterior kit)
Features:

• Manual leveling system is accurate to ±1/4'' per 100'.
• Multi-voltage adapter accepts XRâ„¢, XR+â„¢ and compact DEWALT batteries 9.6V - 18V.
• Dual side-by-side laser diodes for an extremely bright, visible beam.
• Protected rotary head & side impact roll cage for increased durability.
• Built-in wall, floor and tripod mounts allow fast and easy setup for most common applications - eliminates need for separate tool mount accessories.
• Two-position pivoting head for quick adjustment from level to plumb.
• Built-in bump sensor alerts user if laser has been bumped after leveling.
• Variable speed, 0-600 RPM for increased visibility.
• Digital laser detector extends interior & exterior range to 600'.

Spectra Precision Laser HD50

Features

• One-person, ‘non-contact’ distance measuring up to 165 ft (50 m)
• Accuracy of 1/16 in (1.5 mm) across the entire measuring range
• ‘Area’, ‘volume’, and ‘continuous measurement’ keys allow direct access to measurement functions
• Visible red laser beam allows fast targeting
• Intuitive user keypad is simple and easy to use
• Built-in sighting system and waterproof to IP54 for easy outdoor use
• Operates over one year on four ‘AAA’ batteries